索尼牌系列彩色电视机I2C总线调整数据大全

1: K系列(G3机芯)数据表

            项 目      

编 号

      调 整      

项 目

      数 据      

范 围

      标 准50Hz      

正常 宽屏

      数 据60Hz      

正常 宽屏

      注 解      控制电路              00      RGB      00－0F      07      07      07      07      RGB 图像      CXA1587S              01      SCN      00－0F      08      06      08      06      副对比度      CXA1587S              02      VM      00－03      02      02      02      02      VM(速度调制)电平      CXA1587S              03      SCL      00－0F      08      07      08      07      副彩色      CXA1587S              04      SHU      00－0F      08      08      08      08      副色调      CXA1587S              05      SBR      00－0F      1F      1F      1F      1F      副亮度      CXA1587S              06      ABL      00－03      03      03      02      02      ABL方式      CXA1587S              07      GDR      00－3F      1F      1F      1F      1F      绿枪激励      CXA1587S              08      BDR      00－FF      1F      1F      1F      1F      蓝枪激励      CXA1587S              09      GCT      00－0F      07      07      07      07      绿枪截止点      CXA1587S              0A      BCT      00－0F      07      07     &

 

nbsp;07      07      蓝枪截止点      CXA1587S              0B      AKR      00－FF      7F      7F      7F      7F      AKB(自动白平衡)关断红截止      CXA1587S              0C      AKG      00－FF      7F      7F      7F      7F      AKB(自动白平衡)关断绿截止      CXA1587S              0D      AKB      00－FF      7F      7F      7F      7F      AKB(自动白平衡)关断蓝截止      CXA1587S              0E      GMA      00－0F      0C      0C      0C      0C      Y 控制      CXA1587S              0F      DCT      00－03      00      00      00      00      直流转换      CXA1587S              10      DPI      00－03      03      03      03      03      选择图像      CXA1587S              11      YFI      00－3F      22      22      22      22      亮度信号滤波器调整      CXA1578S              12      SHL      00－01      01      01      01      01      锐度限幅      CXA1587S              13      YDL      00－0F      07      07      07      07      亮度信号延迟调整      CXA1587S              14      YSW      00－03      01      01      01      01      Y-SW输入      CXA1587S              15      HSH      00－3F      24      24      28      28      水平移位      CXA1587S              16      POV      00－0F      08      08      08      08      完成前      CXA1587S&nb

 

sp;             17      SHF      00－03      02      02      02      02      锐度后      CXA1587S              18      SSH      00－03      01      01      02      02      副锐度      CXA1587S              19      RMT      00－01      00      00      00      00      红抑制      CXA1587S              1A      GMT      00－01      00      00      00      00      绿抑制      CXA1587S              1B      BMT      00－01      00      00      00      00      蓝抑制      CXA1587S              1C      AG1      00－01      00      00      00      00      老化 1(白)      CXA1587S              1D      AFK      00－01      00      00      00      00      AKB(自动白平衡)关断      CXA1587S              1E      SMD      00－01      00      00      00      00      扫描方式      CXA1587S              1F      VEX      00－01      00      00      00      00      V 扩展      CXA1587S              20      AFC      00－03      03      03      03      03      AVC环路增益      CXA1587S              21      AFF      00－01      01      00      00      00      AFC关断      CXA1587S              22      RFP      00－01      00      00      00      00      基准位置      CXA1587S              23      VSZ      00－3F&nb

 

sp;     1E      1E      1A      1A      埸幅      CXD2018Q              24      VSF      00－3F      2E      2E      32      32      垂直移位      CXD2018Q              25      SCR      00－F      08      08      08      08      S校正      CXD2018Q              26      VLN      00－F      08      08      08      08      埸线性      CXD2018Q              27      HSZ      00－3F      0C      0C      0E      0E      行幅      CXD2018Q              28      PAP      00－3F      2E      2E      2E      2E      枕形失真幅度      CXD2018Q              29      TLT      00－0F      09      09      09      09      倾斜      CXD2018Q              2A      UCP      00－0F      0A      0A      0A      0A      上角枕形失真      CXD2018Q              2B      LCP      00－0F      0C      0C      0C      0C      下角枕形失真      CXD2018Q              2C      VBW      00－0F      08      08      08      08      垂直弓形失真      CXD2018Q              2D      VAG      00－0F      08      08      08      08      对角失真(平行四边形)      CXD2018Q              2E      HVV      00－07      04      04      04      04      行埸补偿埸      CXD2018Q              2F      HVH      00－07      00      00      00      00   &nb

 

sp;  行埸补偿行      CXD52018Q              30      FCL      00－07      03      03      03      03      子画面框颜色选择      SDA9188              31      FON      00－01      01      01      01      01      子画面框开关      SDA9188              32      DLY      00－07      00      00      00      00      选择延迟LL 3P      SAD9188              33      P-V      00－0F      07      07      07      07      子画面垂直位置      SAD9188              34      PVS      00－07      04      04      04      04      画中画垂直补偿      SDA9188              35      P-H      00－3F      0A      0A      07      07      子画面水平位置      SDA9188              36      PHS      00－0F      07      07      03      03      子画面水平补偿      SDA9188              37      CTR      00－0F      0AQ      0A      0A      0A      子画面对比度      SDA9188              38      FWV      00－01      01      01      01      01      垂直框宽度      SDA9188              39      FWH      00－01      01      01      01      01      水平框宽度      SDA9188              3A      DVI      00－0F      07      07      07      07      设置延迟 VSI      SDA9188              3B      DVP      00－0F      0F      0F      0F      0F      延迟VSP脉冲      SDA9188              3C&n

 

bsp;     BRT      00－0F      0C      0C      0C      0C      框亮度数据      SDA9188              3D      LEV      00－0F      00      00      00      00      电平调整      TDA9840              3E      STR      00－3F      02      02      02      02      立体声      TDA9840              3F      AXG      00－01      00      00      00      00      辅助输出增益      TDA9840              40      AXM      00－01      00      00      00      00      辅助输出静噪      TDA9840              41      VCX      00－01      00      00      00      00      压腔晶体振荡器频率      TDA9840              42      ERC      00－01      00      00      00      00      误差计数时间      TDA9840              43      MXE      00－01      00      00      00      00      最大允许误差      TDA9840              44      SRO      00－01      00      00      00      00      SRO设置比特      TDA9840              45      ATO      00－00      00      00      00      00      自动选择      TDA9840              46      SYS      00－01      00      00      00      00      制式选择      TDA9840              47      FSW      00－03      00      00      00      00      强制开关      TDA8940              48      SYN      00－01      01      01&

nbsp;     01      01      合成器      TDA9840              49      VCR      00－01      00      00      00      00      VCC基准开关      CXP1315P              4A      SEL      00－FF      5F      5F      5F      5F      分离电平      CXP1315P              4B      DCS      00－3F      　      　      　      　      　      　              4C      UYB      00－3F      　      　      　      　      　      　              4E      HAP      00－3F      　      　      　      　      　      　              4F      HTL      00－3F      　      　      　      　      　      　              50      UCB      00－3F      　      　      　      　      　      　              51      UTL      00－3F      　      　      　      　      　      　              52      LCB      00－3F      　      　      　      　      　      　              53      LTL      00－3F      　      　      　      　      　      　              54      TXP      00－0F      0      0      0      0      图文电视图像      图文处理器              55      ODL      00－FF      10      10      10      10      电源接通延迟      CXP80424              56      OSH 

 

     00－3F      0F      0F      0F      0F      屏显水平位置      CXP80424              57      BLU      00－01      01      01      01      01      蓝背景功能      CXP80424              58      ROC      00－0F      07      07      07      07      旋转中心      CXP80424              59      ROS      00－07      03      03      03      03      步进宽度      CXP80424              5A      HTR      00－3F      1F      1F      1F      1F      水平梯形      CXP80424              5B      MUT      00－01      01      01      01      01      无同步静噪      CXP80424              5C      DID      00－01      00      00      00      00      消磁关闭      CXP80424              5D      OP0      00－FF      * 1      * 1      * 1      * 1      选项 0      CXP80424              5E      OP1      000F      * 2      * 2      * 2      * 2      选项 2      CXP80424      

*输入数据根据彩电型号而定

            项 目      CCD TEXT PinP JPN NICM W.G MTS COMB              KV-K21MN11      0 1 0 0 1 1 0 1              KV-K25MN11      0 1 1 0 1 1 0 1              KV-K29MN11      0 1 1 0 1 1 0 1              KV-K29MH11      0 1 1 0 1 1 0 1      

*输入数据根据彩电型号

            项 目      -- -- -- -- -- MONO TILI DCON CHIN              KV-K21MN11      0 0 0 0 0 0 0 0 1              KV-K25MN11      0 0 0 0 0 0 0 0 1              KV-K29MN11      0 0 0 0 0 0 1 0 1      &

nbsp;       KV-K29MH11      0 0 0 0 0 0 1 0 1      

备注:

1.顺序按遥控器上的“DISPLAY”,“5”,“VOL+”,“POWER”键,电视即进入维修状态.

2.遥控器上的数字键“1”，“4”可向上/向下改变调项目号.用遥控器数字键“3”，“6”可向上/向下改变调整数据值.按“MUTE”键进入数据写入存储方式.按数字键“0”，执行数据写入存储器方式.执行数据写入存储器的操作,将重新调整过的数据值写入EEPROM.按数字键“7”，“0”，所有数据变为存储器中的存储值.按数字键“8”，“0”，使所有数字变为标准数据.按数字键“5”，“0”,进行EEPROM中的数据的初始化.只有更换EERPOM存储器后才进行此项操作,平常不要使用此项操作.按数字键“2”，“0”,将50Hz调整数据写入60Hz工作方式,或反之.

3.行频H-FRP可进维修状态下,电视机输入标准信号,然后按遥按器上的数字键“9”，即可执行频自动调整。

4.按遥控器上的“POWER”键,操作电视进入待机状态..然后按“POWER”键开机,电视机即回到正常工作状态.

2 .索尼F系列(G3F)机芯彩电故障自检功能

1.由于本机芯采用IC总线系统,因此可以实现自检功能.在开机后,若某一受控 IC没有向CPU送回规定应答信号,则说明此IC存在故障,此时与之对应的发光二极管将按规定的次数闪烁(发光二极管点亮600ms的规律闪烁).

2.发光二极管闪烁频率与故障集成电路对

            故障 非易

IC 失性

      

名称 存储器

      AV切换开关 主V/C RGB 偏转数 环绕声

(CXA1545S) (TDA9145) 及扫描 字处理 处理器

      

(CXA1587S) (CXD2018 (TA8776N)

              闪烁      

频率 1

      2 3 4 5 6      

*CPU将按上表所示顺序从左至右对所列出IC进行检查,如果发现故障则对应的二极管开始闪烁.如果两个以上IC同时出障,则位于表中左则顺序的先闪烁.

　

索 尼 系 列 总 线 调 整 数 据

2. S系列彩电KV-S29MH1/S34MH1(G1机芯)数据及调整

            项目      

编号

      调整      

项目

      数 据      

范 围

      标准数据

*2

      

50Hz 60Hz

      50Hz/60Hz      　      

注 解

      受控电路              00      AFC      00－03      00      00      O      AFC开关(03:自由振荡)      CXA1464              01      H-FRE      00－07      45      40      O      行频      CXA1464              02      VFR 50      00－1F      0F      X      X      埸频50      CXA1464              03      CFR 60      00－1F      X      0F      X      埸频60      CXA1464              04      VSH FT      00－1F      0C      0C      O      垂直中心      CXA1461              05      VSIAE      00－3F      26      27      O      埸幅      CXA1464              06      V-LIN      00－0F      07      07      O      埸线性      CXA1464              07      VSC OR      00－0F      07  &nb

 

sp;   07      O      垂直S校正      CXA1464              08      H-PHA      00－0F      03      03      O      水平中心      CXA1464              09      HSIZE      00－1F      12      12      O      行幅      CXA1464              10      PIN AM      00－1F      12      12      O      枕形失真校正幅      CXA1464              11      COR PN      00－07      04      04      O      四角枕形失真      CXA1464              12      PIN-P      00－0F      09      08      O      枕形失真相位      CXA1464              13      Y-BOW      00－3F      24      24      O      埸弓形失真      CXA1464              14      V-ANG      00－3F      23      23      O      埸对角失真      CXA1464              15      H-TRP      00－3F      1F      1F      O      水平梯形失真      CXA1464              16      VCOMP      00－07      03      03      O      亮度变化引起的埸幅失真校正      CXA1464              17      VSM 50      00－01      00      X      X      埸同步范围开关(埸频50时)      CXA1464              18      VSM 60      00－01      X      00      X      埸同示范围开关(埸频60时      CXA1464              19      DSH FT      00－3F      0C      0C      O      直流电平移(水平静会聚微调)      CXA14645              20      UYB OW      00－3F      25      25      O      垂直上角弓形失真      CXA1464           &n

 

bsp;  21      LYB OW      00－3F      25      25      O      垂直下角弓形失真      CXA1464              22      H.AMP      00－3F      1F      1F      O      H,AMP(行幅)      CXA1464              23      HTILT      00－3F      1F      1F      O      水平倾斜      CXA1464              24      UCB OW      00－3F      1F      1F      O      上部偏中弓形失真(U.C.BOW)      CXA1464              25      UTILT      00－3F      1F      1F      O      上部倾斜      CXA1464              　      　      　      　      　      　      　      　              26      LCB OW      00－3F      1F      1F      O      上部偏中弓形失真(U.C.BOW)      CXA1464              27      LTILT      00－3F      1F      1F      O      下部倾斜      CXA1464              28      SBPIC      00－1F      0D      0D      X      副图像(对比度)      CPU              29      SBHUUE      00－1F      0D      0D      X      副色调      CPU              30      SBCOL      00－1F      0D      0D      X      副彩色      CPU              31      SBBRT      00－1F      0D      0D      X      VM      00－01      0      0      X      速度调制(VM)功能接通/断开      　              35      M-DSP      00－3F      35      35      X      主屏幕显示位置水平方向      　              36      S-DSP&nbs

 

p;     00－3F      0E      0E      X      画中画屏幕显示位置方向      　              37      PIP-H      00－3F      20      20      O      画中画水平位置校正      SDA9089              38      PP-V      00－0F      08      08      O      画中画垂直位置校正      SDA9089              39      PIP-L      00－0F      X      X      X      画中画输出电平      SDA9089              40      PIP-C      00－07      04      04      X      画中画框颜色      SDA9089              41      PIP-D      00－07      00      00      O      画中画延迟      SDA9089              42      PIPVS      00－07      04      04      O      画中画垂直校正      SDA9089              43      PIPHS      00－0F      07      04      O      画中画水平校正      SDA9089              44      TXPIC      00－0F      05      05      X      图文图像      　              45      BLUE      00－01      1      1      X      无信号蓝背景功能通\断      　              46      OSD OE      00－01      0      0      X      CRT屏幕显示奇/偶转换位置      　              47      OSD-V      00－1F      0F      0F      X      垂直CRT屏幕显示开始设置      　              48      DEG AU      00－01      　      　      X      消磁功能接通/断开      　              49      OND LY      00－FF      80      80      X      电源接通延迟时间      　   &n

bsp;          50      MUTE      00－01      01      01      X      无信号音频静噪功能接通/断开      　      

　

*1: 50为PAL制输入信号时的标准数据.60为NTSC制输入信号时的标准数据.

*2: 标有 “O”符号的项目.其调整数据对于埸频为50Hz/60Hz时是不同的,而标有 “*X”符号的项目,其调整数据在埸频50Hz或60Hz 时相同.

注: 08 H-PHA在数据00－07内调整. 34 VM功能不起作用. 46 OSDOE设置为0.48 DEGAUSS设置为0.39 PIP-L在使用M37204M8-A10SP(MM` t IC005)时设置为08. 50 MUTE在使用M3720M8-A10SP时不能选择. 32 SBSHP在使用M37204M8-A10SP时设置为03.在使用M3720M8-XXX时设置为0.

(2)图像质量调整

第28－233’项调整项目,副控制调.在电视对比度,色调,色度,亮度等控制置于50%位置时,若图像不在最佳位置,应对相应的副对比度,副色调,副色度(副彩色),副亮度进行调整.第32,33项副清晰度和平衡控制应设为标准值.

(3)显示位置调整

调整项目号为35－43.第35项,M-DSP,主屏幕水平显示位置,对此项目调整时,屏幕的行幅将从右侧沿水平方向变化.第36 项,S-DSP,画中画屏幕水平显示位置.对比项进行调整时,子屏幕的行幅将从右侧沿水平方向变化.第37项,PIP-H,画中画水平位置校正.第38项,-PIP-V,画中画垂直位置校正.第42项,PIPVS,画中画垂直校正.第43项,PIPHS,画中画水平正.当在维修状态按画中画“POSITION”(位置)时,位置将自动循环变化.第39－4项及第47项 应设置为标准值.第44项,TXPIC,图文电视图像.此项目的目的是当接收图文电视时校正亮度,标准值是05.

　

索尼G系列彩电I²C总线数据调整

(1)令彩电进入行待机状态.(2)依次按键:DISPLAY”,5”.VOL(+)”,POWER”,彩电便进入维修模式.(3)按键.1”,4”,可选择所需调整的项目号(如01,08, 0A等).按键3”,6”,可调整数据.(4)按键MUTING”写入.(5)按键0”实行写入,此时屏幕显示WRITE”表示数据已写入,调整即告结束.对于一般维修而言,若不需对某项目数据作仔细或特别的调整,可在彩电进入维修模式之后,直接依次按动8”,0”键,即可迅速调好IC总线数据(全标准状态).

            项目号      调整项目      数据范围      初始数据      标准数据      注      器件              00      HSF      00－3F      24      50:21 60:26      水平中心      TDA(8366)              01      HSZ      00－3F      23      50:27 60:28      行尺寸      TDA(8366)              02      PAP      00－3F      21      50:25 60:25      行尺寸      TDA(8366)              03      CNP      00－3F      29      50:2D 60:2F      角位指示      TDA(8366)              04      TLT      00－3F      20      50:24 60:20      枕形相位      TDA(8366)              05      VSL      00－3F      20      50:21 60:21      垂直行线性      TDA(8366)              06      VAP      00－3F      1D      50:3E 60:3F      垂直幅      TDA(8366)              07      SCR      00－3F      20      50:29 60:29      线性校正      TDA(8366)              08      VSP      00－3F      20      50:39 60:3A      垂直中心   &

nbsp;  TDA(8366)              09      RDR      00－3F      25      25(Fix)      白点R      TDA(8366)              0A      GDR      00－3F      20      20      白点G      TDA(8366)              0B      BDR      00－3F      20      20      白点B      TDA(8366)              0C      YDL      00－0F      00      00      Y延迟调整      TDA(8366)              0D      FO      00－02      00      TV:00 V:00      飞立浦-一时间常      TDA(8366)              0E      AGC      00－3F      06      TV:06 V:06      自动增益控制(AGC)接收      TDA(8366)              0F      VSW      00－01      01      TV:00 V:01      视频静调      TDA(8366)              10      FOR      00－03      00      0      强制场频      TDA(8366)              11      DL      00－01      00      0      隔行析像      TDA(8366)              12      POC      00－01      00      0      同步      TDA(8366)              13      NCI      00－01      00      50:00 60:00      垂直分压模式      TDA(8366)              14      VID      00－01      00      50:00 60:00      视频恒等模式      TDA(8366)              15      HCO      00－01      00      50:00 60:00      EH平面T形波跟踪模式      TDA(8366)              16      EVG      00－01      00      50:00 60:00      起动V保护      TDA(8366)              17      SBL      00－01      00      50:00 60:00      作用消隐    

 

  TDA(8366)              18      PRD      00－01      00      50:00 60:00      过压输入      TDA(8366)              19      EXP      00－03      00      00      垂直偏转模式S      TDA(8366)              1A      SFM      00－01      01      01      SWON中的高频      TDA(8366)              1B      PHL      00－01      00      00      彩色晶体锁相环      TDA(8366)              1C      COR      00－01      00      00      噪声核化峰值      TDA(8366)              1D      PMX      00－3F      20      20      图像最大数据      TDA(8366)              1E      SBR      00－7F      4B      53      副亮度      TDA(8366)              1F      SHU      00－0F      07      07      副色调      TDA(8366)              20      SSH      00－03      01      TV:01 V:03      副锐度      TDA(8366)              21      SCL      00－3F      3F      50:3F 60:3F      副彩色      TDA(8366)              22      TXP      00－0F      09      09      文本图像控制      (SAA5281)              23      MXP      00－0F      0B      0B      文本混合模式图像      (SAA5281)              24      ODL      00－FF      10      10      电原ON延迟      CXP85200              25      OFR      00－0F      00      00      遥控器RGB OUT      CXP85200              26      OFM      00－0F      00      00      主电原RGB OUT      CXP85200&nbs

p;             27      OSH      00－3F      0A      06      0SD(状况屏幕显示)位置H      CXP85200              28      MUT      00－01      01      00      非同步静调      CXP85200              29      ABL      00－01      01      01      亮度ABL      CXP85200              2A      OPO      00－FF      40      2B      选购件0      CXP85200              2B      OP1      00－FF      07      07      选购件1      CXP85200